ORTUR Laser Master 2 Pro S2 LU2-2 24V Laser Engraver Engraving Cutting Machine. [Ortur new upgrade pro model] Laser Master 2 Pro S2 LU2-2 is newly upgraded, adding new functions such as flame detection, emergency stop, etc. With stronger system reliability, smooth engraving, faster engraving speed, higher accuracy, and more refined engraving products.
The new upgrade brings users a better experience! [Overall optimization] Laser Master 2 Pro S2 LU2-2 has a longer service life, because the mechanical structure has been optimized and designed to have a faster speed and can work stably for a long time.At the same time, Ortur Laser Master 2 Pro can provide users with more security because it has more security features. Because it is equipped with the latest OLM-PRO-V10 motherboard, the engraving is smoother and more delicate, the engraving accuracy is higher, and the speed is faster.
The circuit system with 24V voltage is upgraded, the current is lower, and the system is safer. Update Ortur Laser 1.8 firmware, which is the most advanced laser engraving machine firmware at present, with more powerful functions. Support Ortur offline control screen. [Product advantage] Ortur Laser 1.8 firmware is based on OLF1.4 firmware upgrade, optimizes the motion algorithm, and increases the maximum motion speed from 4000mm/min to 10000mm/mm.The focus of the LU2-2 laser module is smaller because of it. It is the second-generation FAC laser module, the focal point is only 0.070.06mm, and the focal area is about a quarter of the first-generation 0.230.23mm. So he can cut through 3mm plywood and 6mm pine board at a time. When the engraving machine is displaced or tilted, it will automatically stop the laser to prevent damage to the target from the laser; 2. When the engraving machine or computer crashes, the laser will stop working immediately to prevent continuous fire. The engraving machine is turned on, but there is no movement for a long time, it will be protected, and the laser will be turned off automatically. Flame Detector + Buzzer Alarm 5.
Emergency stop switch for emergency. ORTUR Laser Master 2 PRO S2 LU2-2 is better at engraving exquisite patterns, and it has a very small spot which can meet the needs of engraving various complex patterns. It is not that the smaller the light spot, the better the effect. When engraving photos, you may need to increase the laser spot to get a better picture effect. The competitors may falsely promote the power of similar laser modules as 40W, or even 60W, please take care.
Focal Length:It has a shorter Focal Length, so it has a smaller Focal Spot, but shorter Depth of Field. Extra Accessories:Safety Glasses, 10PCS Metal Business Cards, 2PCS Color Paper, 4PCS Pet ID Tags. ORTUR LASER 1.8 SERIES FIRMWARE. ORTUR Laser 1.8 firmware, qualified for ESP 32 MCUs, optimize the motion algorithm, and increases the maximum stepper motors speed from 4000mm/min to 10000mm/mm. It can re-process 32 instructions, the craving is smoother and more delicate, the craving precision is higher, and the speed is faster.This laser engraver supports PWM mode. Pre-assembled parts, just need 10 - 20 minutes to install the machine. 400 x 400 mm large engraving area. Aluminum profile frame + structured cabling, solid structure, smooth operation, attractive appearance. Synchronizing shaft mechanical structure, avoid out-sync on two Y rails, during full speed engraving. Flame Detector & Buzzer Alarm: When the laser engraver detects flame, it will automatically stop and beep. Emergency Stop: There is a switch for emergency stop.
Once there is a emergency in the process of engraving, you can press the emergency stop switch to stop engraving. Active Position Protection: There is a G-sensor on the motherboard.Once the laser engraver detects unauthorized movement, the laser beam will stop. Laser Beam Safety Guard: If your computer system halted or USB cable disconnected and then the laser engraver stops moving, the laser beam will stop to prevent fire. Exposure Duration Detection and Limitation: Once the laser cutter is under control but the users forget to operate it, the motor will stopped working. And then the laser beam will stopped after a while to prevent fire. Power Control System: Once the laser engraver disconnect to the power, it would cut the power to the laser module. New Eye Protection Design: Adopts newly laser protective cover, the ORTUR laser engraving machine can filter out 98% UV light to perfectly protect your eyes to reduce the cost of your goggles and the inconvenience of wearing goggles. Immediately you paid for the order. Communication always is best way to solve problem. We accept any return in 14 or 30 days that we promise. Please never return the parcel without agreement. From us, it is no possible for us to get the parcel. Because the Ratings below 5 are equal to You are NOT satisfied. Your recognition is our motivation in developing our small company and improving our service for each customer. It'll take you one minute only. If you're not satisfied with our goods or service, please write to us immediately so that we can help you out. Sincerely hope you do not leave us any negative or neutral feedback. Communication is very important, we believe we can resolve all the problem with each other. We will give you the best advise. We welcome to answer any questions you have.