Upgraded Engraving with Air Assist System: The S30 series is equipped with an airassist 32-bit motherboard and a control-type air pump, which can intelligently control the air-assist switch during engraving through the LightBurn software button, this makes the engraving and cutting very, and is very suitable for the manufacture of exquisite gifts. Engraving Performance: S30 5W is high cost-effective and can meet 90% of hobby needs; It can cut 5mm balsa wood and 3cm plywood at. And making it reach industrial-grade engraving accuracy with extremely solid and high- linear slide rail X-, no e wavy pattern in carving small items.
410400mm large-area engraving can meet your various engraving needs. Built-in high pressure air assist nozzle: S30 series is equipped with high-pressure air-assisted metal nozzle, which can generate high-pressure airflow under the air pump, greatly improving the cutting efficiency, and the cutting speed is more than 5 times faster than that without air assistance. The powerful airflow blows away the residue, making the cut surface very. Replaceable protective lens: Adopts innovative replaceable lens, greatly improves the service of the, which is more than 10 times longer than other general lasers.
When the lens is damaged or after long-term use, the lens can be replaced to restore the cutting. Eye and Safety Design: equipped with a detachable eye, which will not even without glasses.If you don't need it, you can easily disassemble it. The presented A4 size steel pad can well the table from damage. There is a very and eye-catching switch on the machine, you can directly and quickly turn off the in an. Sturdy and Frame: The S30 series is made of high-strength alloy, its frame can bear up to 50KG weight without damage, and is very.
The frame can be used for a long and maintain high, only need to upgrade the latest when the machine needs to be upgraded. And there are precise scale lines on the X- and Y- which is convenient for you to quickly measure the size of the engraved object. Specification: Model: SCULPFUN S30 Input: AC, 50/60HZ Output: 5A Engraving accuracy: 0.005mm Engraving area size: 410400mm Machine : about 60W Diode output : 5W (note that this is energy not electrical energy) : 0.06x0.06mm wavelength 455±5nm Focusing method: fixed column + sliding device cover: Equipped with a detachable cover to the eyes. You can adjust it up and down, or remove the. Air pump: Type: mainboard-controlled air pump, voltage, 30L/min Air hose inner diameter: 7.5mm Engraving material: all kinds of wood (including walnut, cherry and other high-density wood), MDF,, cardboard,, leather, board, oxide, 304 stainless steel, ceramic, dark stone Cutting material: all kinds of wood (including walnut, cherry and other high-density wood), MDF, acrylic board, cardboard, non-woven, bamboo, leather, some boards, boards.
Operating software: LightBurn (with air assist function), LaserGRBL, LightBurn, Benbox, GrblController, LiteFire, support system, support system. Supported file formats NC, BMP, JPG, PNG, DXF and other formats. Data transmission method: USB connection or connection Package Size: 62.3x24x22.5cm/24.5x9.4x8.8in Package Weight: 6.7kg/14.7lb. Because of the powerful, it is forbidden to run the engraving machine without being supervised.
Pause it if you're not around. For detailed machine instructions, please refer to the manual for parameter settings.When operating the engraving machine, please install the protective cover; if it is not installed, you need to wear. Do not the with your hands, otherwise you may burn your hands.
Please strong impact on the machine. It is forbidden for children under 14 years old to use this product, and over 14 years old need supervision. Do not apply the directly to any specular reflection object, which may cause injury to the operator or burn the.
Packing List: 1 x S30 1 x Kit 1 x automatic air pump 3 x A4 size 3mm wooden board 2 x Limit Switch 1 x 5A 1 x cord 1 x USB cable 1 x Air tube 1 x Installation tool Kit 1 x 1 x A4 metal backing plate Step 1-6 Install the package 1 x Manual 1 x X- assembly 2 x X profiles 2 x Y profiles 1 x Control Box Assembly 3 x support feet.